Dent Removal Tools

Magnets are a great way to locate dent tools when the tooling is in the bore of the instrument! Learn More

Introducing the GirthQuake!! This unique dent rod will allow any tech to remove dents on large and small instruments without major flex in the dent rod. This allows for the best dent work results!! Learn More

Heat-N-Set Low Temperature Moldable Thermoplastic can be easily molded into various shapes from small beads. 

Use Heat-N-Set as grips and extensions on tools you are using, or use as a form to hold tools in place on your bench.
Heat-N-Set can be softened with heat and re-shaped again and again! 

Learn More

We developed the Alto Flute Body Mandrel by special request . Next time an alto flute comes into the shop, you'll be glad you have this custom mandrel for checking straightness, dent work, polishing, and burnishing on alto flutes.

.986" diameter mandrel with 20" working length - 26 1/8"  total length

Learn More

Protection Tape
Blue Low-Tack Tape: 2mm thickness - 1 to 3 oz/in Tack- Low Density Polyethylene
Clear Medium-Tack Tape: 4mm thickness - 4 to 8 oz/in Tack- Low Density Polyethylene

Learn More

An accessory that pairs with the 5/8th or 3/4 inch dent rod. You’ll love how fast, safe, and easy it is to remove dents with a barrel shape.  The Stainless Steel Flute Dent Barrel threads onto the end of the dent rod, and the result is a strong radius for removing dents from the inside of the flute by using pressure on the rod and Dent Barrel. On an extremely damaged flute, use the dent barrel to make way for the body mandrel to go through the body.  It also works great for pushing up low spots on tone holes or raising posts that are low or have been pushed in.

Learn More

Get protection for your valuable dent tools. This durable plastic mesh stretches to conform to the shape of tapered mandrels and keeps them safe from accidental nicks and scratches. The mesh texture raises the mandrel off of the bench top or drawer bottom to keep dirt and grit off of your tools. Available in three size ranges and sold by the foot in uncut lengths. Learn More

It is a real challenge to polish, or rag, a flute body on a mandrel because the flute slides and spins around. Our repair department created the Flute Stabilizer for use with our whole line of flute body mandrels to hold the flute in place to make it easy to polish and perform other tasks which require the flute to be stationary.

The Flute Stabilizer threads on to the end of the mandrel and can be left in place during most uses of the mandrel. Use the included hex key wrench to tighten the end, which expands a rubber gasket to make steady contact with the inside of the flute body, holding it in place. The gasket will only expand to a certain point, which eliminates the risk of over-expanding and causing damage to the flute. 

For use with our Economy, Professional, and Alto Flute Body Mandrels

Learn More

The MusicMedic.com Stainless Steel Saxophone Body Mandrels will change the way you do dent work. These revolutionary mandrel sections were designed by the Sax ProShop team to give you the right taper, no matter which part of the body tube you're working on.

Learn More

Sized to work in larger diameter tubes, This highly polished dent barrel has a more pronounced profile for raising stubborn dents. Great for the bottom end of Tenor and Baritone saxes and saxophone bell sections. Machined with smooth radius edges from rust-resistant magnetic stainless steel.

Learn More

Sized to work in all areas of the body tube, the tenor sax dent barrel is heavy enough to rebound up pushed in posts but shaped to provide great control in working out smaller dents and creases too. Slotted to allow the dent barrel to pass through the neck end of the saxophone without removing the body octave pip or removing the bow. Learn More

An deal shape for pushing for rebounding dents out of an alto saxophone body tube.
Machined with smooth radius edges from rust-resistant magnetic stainless steel. Slotted to allow the dent barrel to pass through the neck end of the saxophone without removing the body octave pip or removing the bow.

Learn More

Beautiful, sleek, stainless steel. We created these in the Sax ProShop and have been using them for years.

Learn More

This Tenon Sizing Tool resulted from a big dream, and a desire to create a lifetime tool with absolute precision and predictability.  The result is a magnificent stainless-steel masterpiece directly from our shop in Wilmington, NC. Size your flute tenons and soprano, alto, tenor, baritone, and bass saxophone tenons with ease. 

Collets sold separately here: Tenon Shrinking Collets

Learn More

Each collet contains a notch to lock into the tool so that when you move the neck, the collet will not spin.
A variety of collets in .5mm increments.

Learn More